To get the best experience while viewing this site, it is recommended that you upgrade to a modern browser version of Chrome or Firefox.

You may do so by clicking on one of these icons:


southern new mexico surgery center
 
  •  

  •  
    Health Library Explorer
    A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A-Z Listings Contact Us
    Interactive Tools

    Gastrostomy Feeding Tube Care: Flushing

    With gastrostomy tube feeding, you need to keep the tube from getting clogged by flushing it with warm water after each feeding and before and after giving any medicines.

    There are different types of gastrostomy feeding tubes. One type has a connection that lets you plug or push the syringe into the feeding tube port. A newer type has a twist-on safety connector. The twist-on safety connector means you must use a specific type of syringe that twists onto your feeding tube port. Check with your care team to make sure you are following the steps for your specific type of gastrostomy tube. Ask for written gastrostomy tube instructions. Review the material with a care team member before you leave the hospital. Don't hesitate to ask questions, take notes, and have the information repeated as many times as needed until it's clear to you.

    Plug-in syringe and tube

    Twist-on syringe and tube

    For continuous feeding

    Flush the feeding tube with warm water and a clean syringe before the first daily feeding, after the last daily feeding, and other times as instructed. Follow the steps below:

    • Fill a clean bowl with warm water.

    • Put the tip of the syringe in the water.

    • Draw up 20 to 30 cc (mL) of water. Follow your provider's specific instructions. The exact amount of water to use will vary depending on your age, condition, and situation.

    • Turn off the pump.

    • Close the clamp on the feeding bag tubing.

    • Remove the tubing from the port.

    • Put the tip of the syringe in the feeding port.

      • Plug-in port. If you have a plug-in feeding tube port, push the tip of the syringe into the feeding tube port.

      • Twist-on port. If you have a twist-on feeding tube port, screw the syringe tip onto your feeding port.

    • Push the plunger down.

    • Let the water run through the feeding tube.

    • Start the feeding or close the cap on the feeding port.

    • Tape the tube to the skin with medical tape.

    Plug-in syringe and tube

    Twist-on syringe and tube

    For bolus feeding

    You may be told to flush the feeding tube before and after each feeding, or just after feedings. Use a clean syringe and warm water. Follow the steps below:

    • Fill a clean bowl with warm water.

    • Put the tip of the syringe in the water.

    • Draw up ____ cc (mL) of water (tap water is OK to use). Follow your provider's specific instructions. The exact amount of water to use will vary depending on your age, condition, and situation.

    • Open the cap on the feeding port.

    • Put the tip of the syringe in the feeding port.

      • Plug-in port. If you have a plug-in type feeding tube port, push the tip of the syringe into the feeding tube port.

      • Twist-on port. If you have a twist-on feeding tube port, screw the syringe tip onto your feeding port.

    • Push down on the plunger. Let the water run through the tube.

    • Close the cap.

    • Tape the tube to the skin with medical tape.

    Online Medical Reviewer: Fraser, Marianne, MSN, RN
    Online Medical Reviewer: Lehrer, Jenifer, MD
    Online Medical Reviewer: Watson, L. Renee, RN, MSN
    Date Last Reviewed: 5/1/2022
    © 2000-2024 The StayWell Company, LLC. All rights reserved. This information is not intended as a substitute for professional medical care. Always follow your healthcare professional's instructions.
    horizontal line

    Southern New Mexico
    Surgery Center

    2301 Indian Wells Rd. Suite B
    Alamogordo, NM 88310
    www.snmsc.org

    Phone: 575.437.0890
    Fax: 575.437.0905
    Email: info@snmsc.org

    Disclaimer